This type of hot children's bed was detected a number of products exist hidden dangers!
hya
hya.com
2018-06-05 11:18:45
This type of hot children's bed was detected a number of products exist hidden dangers!
Bunk beds that do not comply with national standards violate national mandatory standards, which means that these bunk beds are not allowed to be produced and are not allowed to be sold in the market. However, these products that do not meet the national standards are mostly focused on the use of safety.
The inspection personnel introduced that, unlike ordinary furniture, the users of bunk beds are mostly children and belong to children's furniture. Therefore, in accordance with the national standard, furniture products with a height of less than 1m6 in children's furniture must be rounded if they have external corners, and the diameter of rounding should be the smallest that fits the 10mm goniometer.
In this comparative experiment, the edge and tip of a total of 8 samples did not meet the requirements of the national standard and there was a safety hazard.
Sun Shudong, director of the National Furniture and Indoor Environmental Quality Supervision and Inspection Center, is mainly concerned with the lack of product safety awareness. He believes that this product only meets the function, but ignores the damage caused by product design flaws on the human body.
The same is a design issue. Once there is a problem with the distance between the bunk bed ladders, it is easy for children to fall and get injured.
Sun Shudong, director of the National Furniture and Indoor Environmental Quality Supervision and Inspection Center, requires that the distance between the upper and lower surfaces of the ladder be within 200-300mm.
After testing, this comparison test, the ladder of 10 samples does not meet the requirements of national standards. These ladders that do not comply with the national standard are due to the large distance between the lower and upper surfaces of the pedals.
Sun Shudong, director of the National Furniture and Indoor Environmental Quality Supervision and Inspection Center: The main reason for this situation is that companies are trying to reduce their production costs and increase the distance between the ladders. This will save the ladder pedal.
The reporter noted that casualties caused by bunk beds have been continuously reported. Most of these accidents were caused by hidden dangers in going into the bed safety fence, which caused users to fall from the top floor and eventually led to tragedy.
Therefore, it is self-evident that the safety feature of going to bed. The national standard requires that the gap between the safety bars on the bed be between 60-75mm, otherwise it will easily catch the user's legs or arms.
In addition, the guardrail should have a sufficient height, at least to 300mm, and the low guardrail can easily cause the user to fall down. Because of the importance of the bed guardrail, the national standard also requires installation of guardrails that meet the clearance and height requirements.
However, in this comparison test on the safety test of the upper bed, it was found that out of the 28 samples that did not meet the national standard, 27 samples of the safety bar that went out of bed did not meet the requirements of the national standard, which was the highest rate of nonconformity.
The analysis of the inspectors leads to many problems in the barriers, and it is also an enterprise's use of materials to save costs.
The marking line on the bunk bed is a safety line that cannot be ignored
The inspectors pointed out that the main quality problems found in this comparative experiment are not to perform rounding and artificially widen the ladder spacing. The reason behind this is that production companies are trying to save costs.
At the same time, some of the risks associated with the lack of raw materials and the lack of safety awareness cannot be ignored.
According to the national standard, the bunk bed should be marked with a marking line, which is a permanent marking line. It reminds consumers that the height of the mattress plus bedding cannot exceed this line. After testing, it was found that there were a total of 24 products in this comparative trial without this marking line.
Sun Shudong, director of the National Furniture and Indoor Environmental Quality Supervision and Inspection Center, reminds consumers to limit the height of the use of consumer mattresses. If it exceeds this scale, it will cause consumers to fall from bed and cause injury. It can be said that this warning line is a lifeline to protect consumers.
Marker line is the lifeline of consumers. However, nearly 90% of the marking lines that do not cost raw materials are not marked.
However, in this comparison test on the safety test of the upper bed, it was found that out of the 28 samples that did not meet the national standard, 27 samples of the safety bar that went out of bed did not meet the requirements of the national standard, which was the highest rate of nonconformity.
The analysis of the inspectors leads to many problems in the barriers, and it is also an enterprise's use of materials to save costs.
The marking line on the bunk bed is a safety line that cannot be ignored
The inspectors pointed out that the main quality problems found in this comparative experiment are not to perform rounding and artificially widen the ladder spacing. The reason behind this is that production companies are trying to save costs.
At the same time, some of the risks associated with the lack of raw materials and the lack of safety awareness cannot be ignored.
According to the national standard, the bunk bed should be marked with a marking line, which is a permanent marking line. It reminds consumers that the height of the mattress plus bedding cannot exceed this line. After testing, it was found that there were a total of 24 products in this comparative trial without this marking line.
Sun Shudong, director of the National Furniture and Indoor Environmental Quality Supervision and Inspection Center, reminds consumers to limit the height of the use of consumer mattresses. If it exceeds this scale, it will cause consumers to fall from bed and cause injury. It can be said that this warning line is a lifeline to protect consumers.
Marker line is the lifeline of consumers. However, nearly 90% of the marking lines that do not cost raw materials are not marked.
ZHEJIANG HYA INDUSTRY CO.,LTD is a trading and industry company which was built up at 2008 specializing in exporting and purchasing to more than 15 countries . Please click the link Printing mattress Stichbond fabric factory to read more interesting news.